可能发错区了，来这里咨询个 Cisco PoE 交换机与 Netgear PD 交换机的兼容性问题
hrzhm 2018-01-03 12:32:11 +08:00 4461 次点击这是一个创建于 2842 天前的主题，其中的信息可能已经有所发展或是发生改变。
Cisco 的 PoE 协议和 Netgear 的号称都是支持 802.3af 和 802.3at 的
实际我用 2960L-16PS 给 Netgear 的 GS105PE 供电，供电能识别到，但是网络连接无法识别
这个有没有什么兼容性的配置参数的= =
表现就是，端口快速 UP/DOWN 一次，然后显示未链接
我拔插几次网线的 log：
Dec 31 16:28:33.858: %LINK-3-UPDOWN: Interface GigabitEthernet0/16, changed state to down
Dec 31 16:28:35.136: ILP uses DC Disconnect(Gi0/16): state= ILP_LINK_UP_S, event= IEEE_PD_REMOVAL_EV
Dec 31 16:28:35.136: ilpower delete power from pd linkdown Gi0/16
Dec 31 16:28:35.136: Ilpower interface (Gi0/16), delete allocated power 15400
Dec 31 16:28:35.136: Ilpower interface (Gi0/16) setting ICUT_OFF threshold to 0.
Dec 31 16:28:35.286: ilpower_notify_lldp_power_via_mdi_tlv Gi0/16 pwr alloc 0
Dec 31 16:28:35.286: Gi0/16 AUTO PORT PWR Alloc 130 Request 130
Dec 31 16:28:35.286: Gi0/16: LLDP NOTIFY TLV:
(curr/prev) PSE Allocation: 13000/0
(curr/prev) PD Request : 13000/0
(curr/prev) PD Class : Class 4/
(curr/prev) PD Priority : low/unknown
(curr/prev) Power Type : Type 2 PSE/Type 2 PSE
(curr/prev) mdi_pwr_support: 7/0
(curr/prev Power Pair) : Signal/
(curr/prev) PSE Pwr Source : Primary/Unknown
Dec 31 16:28:35.286: ilpower_notify_lldp_tlv: lldp power class tlv:
Dec 31 16:28:35.286: (curr/prev) pwr value 15400/0
Dec 31 16:28:35.286: %ILPOWER-5-IEEE_DISCONNECT: Interface Gi0/16: PD removed
Dec 31 16:28:35.860: ILP uses DC Disconnect(Gi0/16): state= ILP_DETECTING_S, event= PHY_LINK_DOWN_EV
Dec 31 16:28:37.086: ILP uses DC Disconnect(Gi0/15): state= ILP_DETECTING_S, event=ILP_IEEE_PWR_GOOD_EV_SYS_PWR
Dec 31 16:28:37.086: %ILPOWER-7-DETECT: Interface Gi0/15: Power Device detected: IEEE PD
Dec 31 16:28:37.086: Ilpower PD device 3 class 7 from interface (Gi0/15)
Dec 31 16:28:37.086: ilpower new power from pd discovery Gi0/15, power_status ok
Dec 31 16:28:37.086: Ilpower interface (Gi0/15) power status change, allocated power 15400
Dec 31 16:28:37.086: ilpower_notify_lldp_tlv: lldp power class tlv:
Dec 31 16:28:37.086: (curr/prev) pwr value 15400/0
Dec 31 16:28:37.086: ilpower_notify_lldp_power_via_mdi_tlv Gi0/15 pwr alloc 15400
Dec 31 16:28:37.086: Gi0/15 AUTO PORT PWR Alloc 130 Request 130
Dec 31 16:28:37.086: Gi0/15: LLDP NOTIFY TLV:
(curr/prev) PSE Allocation: 13000/0
(curr/prev) PD Request : 13000/0
(curr/prev) PD Class : Class 4/
(curr/prev) PD Priority : low/unknown
(curr/prev) Power Type : Type 2 PSE/Type 2 PSE
(curr/prev) mdi_pwr_support: 7/0
(curr/prev Power Pair) : Signal/
(curr/prev) PSE Pwr Source : Primary/Unknown
Dec 31 16:28:37.086: %ILPOWER-5-POWER_GRANTED: Interface Gi0/15: Power granted
Dec 31 16:28:39.760: ILP uses DC Disconnect(Gi0/15): state= ILP_LINK_UP_S, event= PHY_LINK_UP_EV
Dec 31 16:28:41.757: %LINK-3-UPDOWN: Interface GigabitEthernet0/15, changed state to up
Dec 31 16:28:41.757: ilpower_powerman_power_available_tlv: about sending patlv on Gi0/15
Dec 31 16:28:41.757: req id 0, man id 1, pwr avail 15400, pwr man -1
Dec 31 16:28:43.858: %LINK-3-UPDOWN: Interface GigabitEthernet0/15, changed state to down
Dec 31 16:28:45.860: ILP uses DC Disconnect(Gi0/15): state= ILP_LINK_UP_S, event= PHY_LINK_DOWN_EV
Dec 31 16:28:52.083: ILP uses DC Disconnect(Gi0/15): state= ILP_LINK_UP_S, event= IEEE_PD_REMOVAL_EV
Dec 31 16:28:52.083: ilpower delete power from pd linkdown Gi0/15
Dec 31 16:28:52.083: Ilpower interface (Gi0/15), delete allocated power 15400
Dec 31 16:28:52.083: Ilpower interface (Gi0/15) setting ICUT_OFF threshold to 0.
Dec 31 16:28:52.233: ilpower_notify_lldp_power_via_mdi_tlv Gi0/15 pwr alloc 0
Dec 31 16:28:52.233: Gi0/15 AUTO PORT PWR Alloc 130 Request 130
Dec 31 16:28:52.233: Gi0/15: LLDP NOTIFY TLV:
(curr/prev) PSE Allocation: 13000/0
(curr/prev) PD Request : 13000/0
(curr/prev) PD Class : Class 4/
(curr/prev) PD Priority : low/unknown
(curr/prev) Power Type : Type 2 PSE/Type 2 PSE
(curr/prev) mdi_pwr_support: 7/0
(curr/prev Power Pair) : Signal/
(curr/prev) PSE Pwr Source : Primary/Unknown
Dec 31 16:28:52.233: ilpower_notify_lldp_tlv: lldp power class tlv:
Dec 31 16:28:52.233: (curr/prev) pwr value 15400/0
Dec 31 16:28:52.233: %ILPOWER-5-IEEE_DISCONNECT: Interface Gi0/15: PD removed
交换机上端口状态一直是：
GigabitEthernet0/16 is down, line protocol is down (notconnect)
多次拔插偶尔可以识别到一两次
Dec 31 16:41:07.935: %ILPOWER-5-IEEE_DISCONNECT: Interface Gi0/15: PD removed
Dec 31 16:41:24.739: %ILPOWER-7-DETECT: Interface Gi0/15: Power Device detected: IEEE PD
Dec 31 16:41:24.739: %ILPOWER-5-POWER_GRANTED: Interface Gi0/15: Power granted
Dec 31 16:41:29.358: %LINK-3-UPDOWN: Interface GigabitEthernet0/15, changed state to up
Dec 31 16:41:31.459: %LINK-3-UPDOWN: Interface GigabitEthernet0/15, changed state to down
Dec 31 16:41:36.289: %ILPOWER-5-IEEE_DISCONNECT: Interface Gi0/15: PD removed
Dec 31 16:41:46.890: %ILPOWER-7-DETECT: Interface Gi0/15: Power Device detected: IEEE PD
Dec 31 16:41:46.890: %ILPOWER-5-POWER_GRANTED: Interface Gi0/15: Power granted
Dec 31 16:41:51.958: %LINK-3-UPDOWN: Interface GigabitEthernet0/15, changed state to up
Dec 31 16:41:54.059: %LINK-3-UPDOWN: Interface GigabitEthernet0/15, changed state to down
Dec 31 16:41:57.258: %LINK-3-UPDOWN: Interface GigabitEthernet0/15, changed state to up
Dec 31 16:41:58.258: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0/15, changed state to up
这次就是成功协商好的，正常能用- -
HOMEX#sh interfaces gigabitEthernet 0/15
GigabitEthernet0/15 is up, line protocol is up (connected)
Hardware is Gigabit Ethernet, address is 009a.d2d5.b98f (bia 009a.d2d5.b98f)
MTU 1522 bytes, BW 1000000 Kbit/sec, DLY 10 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation ARPA, loopback not set
Keepalive set (10 sec)
Full-duplex, 1000Mb/s, media type is 10/100/1000BaseTX
input flow-control is off, output flow-control is unsupported
ARP type: ARPA, ARP Timeout 04:00:00
Last input 00:32:06, output 00:00:00, output hang never
Last clearing of "show interface" counters never
Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0
Queueing strategy: fifo
Output queue: 0/40 (size/max)
5 minute input rate 0 bits/sec, 0 packets/sec
5 minute output rate 4000 bits/sec, 7 packets/sec
169 packets input, 26005 bytes, 0 no buffer
Received 139 broadcasts (89 multicasts)
0 runts, 0 giants, 0 throttles
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored
0 watchdog, 89 multicast, 0 pause input
0 input packets with dribble condition detected
1494 packets output, 143925 bytes, 0 underruns
0 output errors, 0 collisions, 1 interface resets
0 unknown protocol drops
0 babbles, 0 late collision, 0 deferred
0 lost carrier, 0 no carrier, 0 pause output
0 output buffer failures, 0 output buffers swapped out
cdp 默认开启，lldp 默认没开，都启用禁用过了，无效
端口强制 speed 1000 和 duplex full，也无效
lldp 最大的帮助就是，在小几率能连上的情况下，PD 受电能识别到 30W，没开 lldp 是 15.4W
可是网络连接还是断的呀还是断的呀！！= =
各位大大有啥建议么？
实际我用 2960L-16PS 给 Netgear 的 GS105PE 供电，供电能识别到，但是网络连接无法识别
这个有没有什么兼容性的配置参数的= =
表现就是，端口快速 UP/DOWN 一次，然后显示未链接
我拔插几次网线的 log：
Dec 31 16:28:33.858: %LINK-3-UPDOWN: Interface GigabitEthernet0/16, changed state to down
Dec 31 16:28:35.136: ILP uses DC Disconnect(Gi0/16): state= ILP_LINK_UP_S, event= IEEE_PD_REMOVAL_EV
Dec 31 16:28:35.136: ilpower delete power from pd linkdown Gi0/16
Dec 31 16:28:35.136: Ilpower interface (Gi0/16), delete allocated power 15400
Dec 31 16:28:35.136: Ilpower interface (Gi0/16) setting ICUT_OFF threshold to 0.
Dec 31 16:28:35.286: ilpower_notify_lldp_power_via_mdi_tlv Gi0/16 pwr alloc 0
Dec 31 16:28:35.286: Gi0/16 AUTO PORT PWR Alloc 130 Request 130
Dec 31 16:28:35.286: Gi0/16: LLDP NOTIFY TLV:
(curr/prev) PSE Allocation: 13000/0
(curr/prev) PD Request : 13000/0
(curr/prev) PD Class : Class 4/
(curr/prev) PD Priority : low/unknown
(curr/prev) Power Type : Type 2 PSE/Type 2 PSE
(curr/prev) mdi_pwr_support: 7/0
(curr/prev Power Pair) : Signal/
(curr/prev) PSE Pwr Source : Primary/Unknown
Dec 31 16:28:35.286: ilpower_notify_lldp_tlv: lldp power class tlv:
Dec 31 16:28:35.286: (curr/prev) pwr value 15400/0
Dec 31 16:28:35.286: %ILPOWER-5-IEEE_DISCONNECT: Interface Gi0/16: PD removed
Dec 31 16:28:35.860: ILP uses DC Disconnect(Gi0/16): state= ILP_DETECTING_S, event= PHY_LINK_DOWN_EV
Dec 31 16:28:37.086: ILP uses DC Disconnect(Gi0/15): state= ILP_DETECTING_S, event=ILP_IEEE_PWR_GOOD_EV_SYS_PWR
Dec 31 16:28:37.086: %ILPOWER-7-DETECT: Interface Gi0/15: Power Device detected: IEEE PD
Dec 31 16:28:37.086: Ilpower PD device 3 class 7 from interface (Gi0/15)
Dec 31 16:28:37.086: ilpower new power from pd discovery Gi0/15, power_status ok
Dec 31 16:28:37.086: Ilpower interface (Gi0/15) power status change, allocated power 15400
Dec 31 16:28:37.086: ilpower_notify_lldp_tlv: lldp power class tlv:
Dec 31 16:28:37.086: (curr/prev) pwr value 15400/0
Dec 31 16:28:37.086: ilpower_notify_lldp_power_via_mdi_tlv Gi0/15 pwr alloc 15400
Dec 31 16:28:37.086: Gi0/15 AUTO PORT PWR Alloc 130 Request 130
Dec 31 16:28:37.086: Gi0/15: LLDP NOTIFY TLV:
(curr/prev) PSE Allocation: 13000/0
(curr/prev) PD Request : 13000/0
(curr/prev) PD Class : Class 4/
(curr/prev) PD Priority : low/unknown
(curr/prev) Power Type : Type 2 PSE/Type 2 PSE
(curr/prev) mdi_pwr_support: 7/0
(curr/prev Power Pair) : Signal/
(curr/prev) PSE Pwr Source : Primary/Unknown
Dec 31 16:28:37.086: %ILPOWER-5-POWER_GRANTED: Interface Gi0/15: Power granted
Dec 31 16:28:39.760: ILP uses DC Disconnect(Gi0/15): state= ILP_LINK_UP_S, event= PHY_LINK_UP_EV
Dec 31 16:28:41.757: %LINK-3-UPDOWN: Interface GigabitEthernet0/15, changed state to up
Dec 31 16:28:41.757: ilpower_powerman_power_available_tlv: about sending patlv on Gi0/15
Dec 31 16:28:41.757: req id 0, man id 1, pwr avail 15400, pwr man -1
Dec 31 16:28:43.858: %LINK-3-UPDOWN: Interface GigabitEthernet0/15, changed state to down
Dec 31 16:28:45.860: ILP uses DC Disconnect(Gi0/15): state= ILP_LINK_UP_S, event= PHY_LINK_DOWN_EV
Dec 31 16:28:52.083: ILP uses DC Disconnect(Gi0/15): state= ILP_LINK_UP_S, event= IEEE_PD_REMOVAL_EV
Dec 31 16:28:52.083: ilpower delete power from pd linkdown Gi0/15
Dec 31 16:28:52.083: Ilpower interface (Gi0/15), delete allocated power 15400
Dec 31 16:28:52.083: Ilpower interface (Gi0/15) setting ICUT_OFF threshold to 0.
Dec 31 16:28:52.233: ilpower_notify_lldp_power_via_mdi_tlv Gi0/15 pwr alloc 0
Dec 31 16:28:52.233: Gi0/15 AUTO PORT PWR Alloc 130 Request 130
Dec 31 16:28:52.233: Gi0/15: LLDP NOTIFY TLV:
(curr/prev) PSE Allocation: 13000/0
(curr/prev) PD Request : 13000/0
(curr/prev) PD Class : Class 4/
(curr/prev) PD Priority : low/unknown
(curr/prev) Power Type : Type 2 PSE/Type 2 PSE
(curr/prev) mdi_pwr_support: 7/0
(curr/prev Power Pair) : Signal/
(curr/prev) PSE Pwr Source : Primary/Unknown
Dec 31 16:28:52.233: ilpower_notify_lldp_tlv: lldp power class tlv:
Dec 31 16:28:52.233: (curr/prev) pwr value 15400/0
Dec 31 16:28:52.233: %ILPOWER-5-IEEE_DISCONNECT: Interface Gi0/15: PD removed
交换机上端口状态一直是：
GigabitEthernet0/16 is down, line protocol is down (notconnect)
多次拔插偶尔可以识别到一两次
Dec 31 16:41:07.935: %ILPOWER-5-IEEE_DISCONNECT: Interface Gi0/15: PD removed
Dec 31 16:41:24.739: %ILPOWER-7-DETECT: Interface Gi0/15: Power Device detected: IEEE PD
Dec 31 16:41:24.739: %ILPOWER-5-POWER_GRANTED: Interface Gi0/15: Power granted
Dec 31 16:41:29.358: %LINK-3-UPDOWN: Interface GigabitEthernet0/15, changed state to up
Dec 31 16:41:31.459: %LINK-3-UPDOWN: Interface GigabitEthernet0/15, changed state to down
Dec 31 16:41:36.289: %ILPOWER-5-IEEE_DISCONNECT: Interface Gi0/15: PD removed
Dec 31 16:41:46.890: %ILPOWER-7-DETECT: Interface Gi0/15: Power Device detected: IEEE PD
Dec 31 16:41:46.890: %ILPOWER-5-POWER_GRANTED: Interface Gi0/15: Power granted
Dec 31 16:41:51.958: %LINK-3-UPDOWN: Interface GigabitEthernet0/15, changed state to up
Dec 31 16:41:54.059: %LINK-3-UPDOWN: Interface GigabitEthernet0/15, changed state to down
Dec 31 16:41:57.258: %LINK-3-UPDOWN: Interface GigabitEthernet0/15, changed state to up
Dec 31 16:41:58.258: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0/15, changed state to up
这次就是成功协商好的，正常能用- -
HOMEX#sh interfaces gigabitEthernet 0/15
GigabitEthernet0/15 is up, line protocol is up (connected)
Hardware is Gigabit Ethernet, address is 009a.d2d5.b98f (bia 009a.d2d5.b98f)
MTU 1522 bytes, BW 1000000 Kbit/sec, DLY 10 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation ARPA, loopback not set
Keepalive set (10 sec)
Full-duplex, 1000Mb/s, media type is 10/100/1000BaseTX
input flow-control is off, output flow-control is unsupported
ARP type: ARPA, ARP Timeout 04:00:00
Last input 00:32:06, output 00:00:00, output hang never
Last clearing of "show interface" counters never
Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0
Queueing strategy: fifo
Output queue: 0/40 (size/max)
5 minute input rate 0 bits/sec, 0 packets/sec
5 minute output rate 4000 bits/sec, 7 packets/sec
169 packets input, 26005 bytes, 0 no buffer
Received 139 broadcasts (89 multicasts)
0 runts, 0 giants, 0 throttles
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored
0 watchdog, 89 multicast, 0 pause input
0 input packets with dribble condition detected
1494 packets output, 143925 bytes, 0 underruns
0 output errors, 0 collisions, 1 interface resets
0 unknown protocol drops
0 babbles, 0 late collision, 0 deferred
0 lost carrier, 0 no carrier, 0 pause output
0 output buffer failures, 0 output buffers swapped out
cdp 默认开启，lldp 默认没开，都启用禁用过了，无效
端口强制 speed 1000 和 duplex full，也无效
lldp 最大的帮助就是，在小几率能连上的情况下，PD 受电能识别到 30W，没开 lldp 是 15.4W
可是网络连接还是断的呀还是断的呀！！= =
各位大大有啥建议么？
 | 1 Sh888 2018-01-03 13:37:02 +08:00 "实际我用 2960L-16PS 给 Netgear 的 GS105PE 供电" 没有搞错的话，交换机给交换机供电？交换机只能 POE 供电，不能 POE 取电。 |
| 2 Sh888 2018-01-03 13:46:00 +08:00 好吧，是我搞错了。还真可以 POE 取电。 http s://kb.netgear.com/en_US/24268/?_ga=2.64050031.1577813581.1514957999-1275731904.1514957999 GS105PE 15.4W (802.3af) max on ports 1 and 2, not to exceed 19W maximum pass-thru across all connected devices) using an 802.3at (PoE+) source; max limit of 8W pass-through total across ports 1 and 2 using 802.3af (PoE) source 在 cisco 的端口上试一下指定功率，power inline static max 15400 |
| 3 Sh888 2018-01-03 13:47:34 +08:00 直接 1 个 poe 需要支持 poe+，接 2 个只需要支持 poe |
 | 7 tifan 2018-01-05 06:48:18 +08:00 尝试换网线。 |
 | 9 nbsn 2018-01-15 00:54:11 +08:00 需要在思科交换机全局启用 LLDP，(config)# lldp run，在用 show power inline 看一下，所在的接口是否支持 Max 30W。如果想 GS105PE 的 1,2 口正常供电，需要 30W 支持。 我的是 3560CX 连的，工作正常 |
 | 11 yingfengi 2018-01-15 13:13:04 +08:00 via Android poe 交换机给 poe 交换机供电？还有这种操作？ 就算是 at 也才 30W 啊 |
| 13 yingfengi 2018-01-15 18:32:12 +08:00 via Android @hrzhm 是 poe 受电的交换机吧？供电的话，最高才 30W 他怎么给其他设备供。而且多半是 15W 的 |
 | 14 hrzhm OP 受电 30，输出也是 30 很奇怪么- - |
Select Language